|
| HF Antennas - Mobile
Autotune |
9350 Autotune Antenna |
910 Autotune Antenna
|
|
Suits models
NGT,
9323,
8528,
8525A/B,
 The
9350 Auto tune antenna provides for rapid tuning 2 -
28Mhz achieving the lowest possible SWR. Codan's design
and development of this model has set new standards
in performance, reliability and extreme construction
qualities.
- 9350C - Comes complete heavy duty
Stainless Steel Whip (WC2) and Control
cable to suit your model radio
- 9350CS - Same as 9350C but comes
with Spring Base Stainless Steel Whip (WC4)
- 9350TO - Base Tuner Section Only
- Full Specification Sheet - Click
Here
| 9350TO-(Tuner
Only) - $1,045 |
 |
| 9350CS-(Complete
inc.Spring Whip)-$1,379 |
|
| 9350C-(Complete
inc S/S Whip) - $1,295 |
|
|
The 910 Antenna
has been d esigned
to interface with the Barrett 950 / 550 Transceivers.
Providing a frequency coverage of 2
- 30Mhz the Barrett 910 features rapid tuning to a SWR
of typically <1.5:1. High radiation efficiency and
accurate tuning are assured. The antenna also includes
a wideband amplifier to enable efficient channel scanning.
The active tuning elements of the antenna
are housed in a grey weatherproof, impact resistant
reinforced polycarbonate moulding that incorporates
a heavy duty anti-vibration mount at its base.
The 910 antenna is supplied with a 2
metre stainless steel whip and spring and complete with
all cables required
| 910-inc.Control
Cable & Whip -$1,495 |
|
|
|
| Smart
Autotune Antenna Package |
|
Based on the Smartuner SAT01, ultra
compact, rugged and totally waterproof - Lakecomm has
packaged the tuner and specifically customised it to
suit older model radios and most amateur HF transceivers.
HFS3  HFB-2
|
Features inlcude;
- 100 Watts PEP maximum Power Input
- Typical Tuning time < 10msec
- Waterproof Case
- Only requires 12VDC Power and RF
Input
- Tunes off Voice Signal
- 170 non-volatile channel memory locations
ensures ultra rapid tuning
- Tunes between 3.5mHz - 30mHz
Kit Includes;
- SAT01, ATU (Antenna Tuner Unit)
Dimensions 150mm X 180mm X 40mm
- Stainless Steel Whip (2.6m) and H/D
Spring (HS3)
- Antenna Base (HFB-2)
- Control Cable 6m (made to suit)
- Complete customising
Supplied to simply
plug in an operate
|
 HFW |
Complete Package Price - SAT01
- $895
|
-
HF Multi-Tap Antenna
|
18 Tap
|
- Spot Tuned for lowest SWR
- Made from high quality fibreglass
rods
- Resin Coated for long lasting
- Double strengthened base
- Available in 2 models as listed
below with Radtel, HFoZ, RFDS, VKS737 frequencies
- Splits into 2 pieces for easy
storage
- Comes complete in carry bag
Ex03/04
- 1870mm height
|
9 Tap
|
|
Ex03
(Radtel, HFoZ, VKS737
& RFDS) - $398
|
|
Ex04
(RFDS & VKS737) -
$319
|
|
|
| HF Antennas - Portable
and Base |
Portable Antenna-Long Wire |
Portable Antenna-End fed Dipole |
|
 
Spec Sheet - Click
Here
|
- Highly Effecient Resonant Antenna
- Same overall specifications as EX-LW
- Frequency markers to assist selection
- Simple deployment
- Power Rating 100 Watts
- Suitable for portable Manpacks or
temporary base sites
- Spec Sheet -
Click Here
|
|
Specifications EX-LW and
EX-EFD;
- 3-30 Mhz
- No Tuner Required
- Flexiweave wire-infused cord
allowing maximum flexibility
- Waterproof construction
- Weight 800grams
|
Pack Includes;
- Winder
- S/Steel Earth Stake
- 5m Coaxial Cable inc. connectors
- Earth Clip
- Carry Bag
|
|
|
EX-LW-Portable
HF Long Wire $379
|
|
|
|
EX-EFD-Portable
HF Dipole $390
|
|
|
|
- Multi-wire Broadband
Dipole - No tuner
required |
| As shown from the diagrams
below these antennas can be erected in either of two ways,
horizontal between two towers or in an inverted 'V' utilising
one centre tower (minimum 9 metres) and two outrigger
poles approximately 3 metres high. |
|
|
 |
|
Constructed from 2mm stainless steel
wire, the EXHF100 rated to with stand up to 210Klm/hr
winds. All other components are constructed from UV
resistant rods and balun/load boxes - The EXHF100/500
is available in 5 models as listed below - Coaxial cable
supplied separately-
Full Specification sheet - Click
Here
|
|
General Specifications -
- 250 Watts PEP or 1250 PEP Models
available
- 50 Ohm Impedance
- Low SWR
|
- Frequency Range 2.0-30Mhz
- Input Connector - SO239 UHF Socket
- Wire - Stainless Steel - 2mm
|
| Model |
Description and Specifications |
Price |
|
| EXHF100S |
3.6 - 30
Mhz - 250 Watts PEP - 20 metre length |
$495 |
|
| EXHF100 |
2.6 - 30
Mhz - 250 Watts PEP - 27 metre length |
$495 |
|
| EXHF100E |
2 - 30
Mhz - 250 Watts PEP - 54 metre length |
$599 |
|
| EXHF500 |
2.6 - 30
Mhz - 1250 Watts PEP - 27 metre length |
$959 |
|
| EXHF500E |
2 - 30
Mhz - 1250 Watts PEP - 54 metre length |
$1059 |
|
|
|
- Stainless Steel - Heavy Duty including
Spring (HFS4)
- Length 1780mm
- Tunes 2 - 30Mhz
- 14mm Female-Male Thread
|
WC2
+ HS4
|
|
|
WC4
- $148
|
|
|
|
|
- Fibreglass Whip -
Genuine Codan
- Length 1600mm
- Tunes 2- 30Mhz
- 14mm Female Thread
|
Requires H/Duty Spring
|
WC3
- $145
|
|
|
|
|
- Stainless Steel - Heavy Duty
- Genuine Codan
- Length 1680mm
- Tunes 2 - 30Mhz
- 14mm Female Thread
|
Codan as supplied
in Venturer Pack
|
WC2
- $69
|
|
|
|
|
- Stainless Steel, Medium Duty
- Length 1530mm
- Tunes 3 - 30Mhz
- 14mm Female Thread
|
Essential as a back-up
whip
|
WC
- $59
|
|
|
| Codan Spring - Medium Duty |
Codan Spring - Heavy Duty |
|
|
- High Quality Stainless Steel
- !4mm Female - 14mm Male
- Suits WC2 Stainless Steel
Whip as above
|
|
- High Quality Stainless Steel
- !4mm Female - 14mm Male
- Suits WC3 Fibreglass Whip as above
|
|
HFS4 -Spring
$79
|
|
|
|
08-05140-001-Spring
$95
|
|
|
|
|
- Stainless Steel - Heavy Duty
(Genuine Barrett Whip Antenna)
- Length 2120mm
- Includes Spring
- Tunes full band
- 5/16" Female Thread
|
Genuine Barrett Whip
Antenna
|
WB2
- $99
|
|
|
|
|
- Stainless Steel - Medium Duty
- Length 1530mm
- 5/16" Ferrule
- Tunes 3 - 30Mhz
|
Essential as a back-up
whip
|
WB
- $49
|
|
|
|
Antenna
Whips - General
|
|
|
- 2.6m Length - Heavy Duty
- Stainless Steel Tapered
- 1/2" Male Thread
|
| |
|
|
HFW
- $89
|
|
|
|
Antenna
Spring
|
|
|
- Stainless Steel
- 1/2" to 1/2" Female Threads
- Medium Duty Suits HFW Whip
|
|
|
|
HFS3 -Spring
$59
|
|
|
| HF
Antenna Base - Heavy
Duty |
|
| HF
Antenna Base - Medium
Duty |
|
| HF
Antenna Spring- H
Duty |
|
|
- Extreme Heavy Duty
- Constructed from Steel
- Low Loss UHF Connectors
- 1/2" Thread to suit Antenna
- Suits Ex03/04 Tapped Whips above
|
- Made from Heavy Duty Delrin
- 1/2" Male Whip Thread
- SO239 Connector on bottom
|
- Constructed from H/D Double Zinc
Coated Spring Steel
- 1/2" Thread to suit Antenna
- Suits Ex03/04 Tapped Whips above
|
|
|
|
HFB2
- $44
|
|
|
|
HFS-Spring
$69
|
|
|
|
HF Antenna Tuner
|
HF Antenna Tuner -
AT01
- Connects to virtually any HF Radio
- Ideal for Marine and Land applications
- Simply connect to long wire
e.g., Yacht Backstay
- Rapid Tuning in typically milli seconds
- Tune range 1.6 - 30Mhz
- Power input up to 200 Watts
- VSWR typically less than 2:1
- Antenna length - 7 Meters
- Waterproof design
- 12VDC Input
- Includes Control & Coaxial Cable
to suit radio
|
$1,100
Please specify Radio
|
|
|
|
HF Antenna Tuner
SAT01
LAND
- MARINE AMATEUR
|
HF Antenna Tuner -
SAT01
- Connects to virtually any HF Radio
- Ideal for Marine, Land & Amateur
applications
- Simply connect to long wire
(e.g., Yacht Backstay) or Stainless
Steel Whip (HFW) as above
- Rapid Tuning in typically milli seconds
- Tune range 1.8 - 60Mhz (Min 7.5m
Antenna length)
- Power input up to 100 Watts
- VSWR typically less than 2:1
- Waterproof design
- 12VDC Input
- Includes Control & Coaxial Cable
to suit radio
- Dimensions: 230mm x 180mm x 40mm
|
$695
Please specify Radio
|
|
|
|
Vehicle
HF Antenna Mounting Brackets
|
|
|
Rear
Antenna Mounts - Swinging Arm
This vertical antenna mount
has been designed to fit to the exisiting Kaymar Rear
Tyre Mount swinging arm. It simpy just fits over the
RHS arm with 4 fixing bolts. Precision made and zinc
plated for long lasting. The antenna top plate can be
swivalled 360 degrees for optimum positioning. Suits
all HF Antennas.
|
|
|
Rear
Antenna Mounts - Centre Mount
This mounting bracket has been specifically
designed for Lakecomm by Kaymarand is available to suit
6 stud Prado, Pajero, Toyota and Nissan GU Unlike the
standard Kaymar Centre wheel mount this bracket is mounted
behind the wheel enabling far easier removel for those
dreaded times you have a puncture. The rear half of
the bracket permently fixes to the wheel carrier. The
second half fixes to the antenna which then simply bolts
together with 3 fixing bolts.
|
|
|
Rear
Antenna Mounts
Toyota
80 & 100 Series
This mounting bracket has
been designed specifically for Toyota 80,100 series
wagons, tailgate models only. Fitting is as shown in
the picture. Suits both Codan and Barrett Autotune Antennas.
|
80
Series AMHF-TOY80TG
$189
|
|
|
100
Series AMHF-TOY100TG
$189
|
|
|
| Are you NUTS
about your HF? |
|
There's no doubt
everyone could be!
Stop that potential thief
and fit a 'Anti-theft' Locking Nut- It's the cheapest
insurance policy you'll ever purchase!
|
|
The Combination 'Keyed Nut' fits up
completely inside the 'Circular Cover' to prevent
access with a spanner
|
Jenal Selcall/Telcall Microphone
|
SC-2
|
Is
you radio out of date?
Have it
converted!
By
fitting a Jenal Microphone you can bring your
radio up to the latest requirements needed for today's
networks
(Radtel Network / VKS737) and
include such features as;
- Full Selcall & Telcall
- Barrett/Codan/Icom compatible
- Suits most radios
|
Radio
|
Part No.
|
Price |
|
| Codan
8525 |
SC2-8525 |
$599 |
|
| Icom
M710 Kit* |
SC2-M710 |
$595 |
|
| Icom
M802 Kit* |
SC2-M802 |
$595 |
|
| Custom
Radio |
SC2 |
$599 |
|
* The above kits are simply plug in
& use -No modifications to the radio is required
|
Top
All
prices INCLUDE GST and are strictly website sales only
|
